Construir una màquina CNC
Contingut
Introducció
En la present entrada es discuteix bàsicament sobre la construcció de la màquina CNC. Teoria i discussió de CNC a la wiki:
Material
Per fer les rosques (mascles i femelles), es pot trobar al eBay cercant per MACHOS Y TERRAJAS: Per ex (32 PIEZAS MACHOS Y TERRAJAS para roscar o filetear),
- http://www.ebay.es/itm/MACHOS-Y-TERRAJAS-40-PIEZAS-ROSCAR-FILATEAR-COJINETES-TORNILLO-TUERCA-ROSCA-/261430393198?pt=LH_DefaultDomain_186&hash=item3cde77396e
- http://www.ebay.es/itm/32-PIEZAS-MACHOS-Y-TERRAJAS-para-roscar-o-filetear-Cojinetes-Fileras-Abrir-rosca-/230998724951?pt=LH_DefaultDomain_186&hash=item35c898d157
Tornilleria industrial
- Rosques quadrades: M12, 1,75: Alaball suministros industriales, s.l. Sepúlveda, 46 (entre rocafort i entença) 08015 Barcelona Tel 934 240 212
- reyzamadrid@reyzabal.com. | ALAVA, 51 | Tlef. 93 309 10 22 | Fax. 93 300 94 99 | 08005 - BARCELONA 93 309 10 22. No tenen varilles de més d'un metro, però tenen bastanta cosa. El que no tenen és roques quadrades.
Varilla roscada
M12, 1,75. A tot arreu es troben varilles de 1m. Per varilles més llargues:
- Alaball suministros industriales, s.l.
Sepúlveda, 46 (entre rocafort i entença) 08015 Barcelona Tel 934 240 212
Font d'alimentació
36V Regulated Switching Power Supply 9.65A 350W AC/DC PSU
37$
Interface+drivers
CNC 3 Axis Stepper motor paso a paso driver 5A controller & interface tarjeta
69e
Instruccions:
Stepper Motor Driver 5A Driver:
Feature: High performance, cost-effective. Automatic idle-current reduction. DC 12 ~ 48V power supply, the internal integration of 12V and 5V regulator Output current up to 5.0A. Suitable for 2-phase and 4-phase motors. High speed optoelectronic isolation signal input. Single-chip PWM bipolar sinusoidal chopper ensures low vibration and high efficiency. 1, 2, 4 (New Mode), 8, 16 adjustable microstep control, motors run more precisely and smoothly. Equipped with the 3rd generation of breakout board, display panel and control pad to control the motor manually. Overload, overcurrent, overheat, overvoltage and undervoltage protection to avoid damaging your computer and devices. Electrical performance: Input voltage DC 12 ~ 48V input The input current of 1 to 5 amps, select the drive a stepper motor. Output current of 0.2A ~ 5A Temperature Operating Temperature -10 to 45 ℃; Storage temperature -40 ℃ to 70 ℃ Humidity not condensing, not drops Gas prohibit combustible gas and conductive dust Control signal interface: PUL +: step pulse signal is input side or the positive pulse signal input positive terminal PUL-: the negative input of the negative input pulse signal or a positive pulse signal DIR +: stepping direction signal input to the positive terminal or negative pulse signal input to the positive terminal DIR -: stepping direction signal input of the negative side or reverse step pulse signal input negative terminal EN +: offline can reset signal input side is EN-: offline can reset signal input negative terminal Offline enable signal is active, reset drive failure to prohibit any pulse, the output of the drive Power component is turned off, the motor holding torque.
5 Axis Interface Breakout Board:
Feature: 1: The maximum matching 5-axis stepper motor driver 2: The two-stage signal processing, signal transmission smooth, powerful anti-jamming 3:5 input interface to define the emergency stop, limit, points in the knife, etc. 4: relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc 5: five-axis job LED display, visual display products, working condition Electrical performance: Input Power: 5V DC power supply or computer USB to take power Work axis stepper: Received the highest 5-axis independent driving Drive: Pulse + direction + enable signal. Weight: About 200 N=GND, D=dir, S=step, E=enable
Bearing (coixinets, rodaments)
Són els coixinets dels patinets. Se'n necessiten 3*2*4=24 unitats. El diàmetre interior és de 5/16, i aleshores les arandeles poden ser de 6716. Aquests són els coixinets que es necessiten per fer les guies.
Ara bé, els coixinets a través del qual passa la varilla roscada ha de tenir un diàmetre interior de 12mm. Distribuidors de coixinets a l'àrea de Barcelona:
A Badalona:
93 4590618. Per fer el torn de fusta, el que necessito és rodillos de levas ina serie kr (http://www.schaeffler.es/content.schaeffler.es/es/branches/industry/productronic/productronic_product_range/stk/ina_yoke_type_and_stud_type_track_rollers.jsp), que són uns coixinets que tenen un cargol, amb la qual cosa puc ficar una rosca. Els tenen a collvilaro.com
A Hospitalet:
- brammer.biz
Tel. 93 - 451 20 99. Comanda mínima 30e
Llista de distribuidors:
Stepper Motor Coupler Connector
Les meves varilles roscades són de 12mm. Cercar a ebay per Stepper Motor Coupler Connector 12mm
Pressupost
ebaY (mail yahoo/jq********). Paypal (mail yahoo/jq********)
- coixinets (30 unitats): 22,50 EUR
- font d'alimentació 36V 9,65A 350W 37$
Notes
122x80 134x80 4'4'' = 52'' = 132,08 4'1'' = 49'' = 124,46 2'6'' = 30'' = 76,2 2.54cm 30,48 pie12 pulg
Ajuntar 2 peces de DM de 1,9mm
Faig servir les broques de fusta de 6 mm i 12 mm. Els cargols que faig servir són els de 60mm x 6mm diam. El forat de 12mm el faig a 35mm del cantó, i la profunditat a què s'ha de fer és que la punta de la broca quedi 1-2mm per sobre de la peça.
Broca de 6mm: com que el gruix del DM és de 19mm, la meitat és 9,5mm